Fandom

Chip's Challenge Wiki

Chip's Challenge scoring

1,094pages on
this wiki
Add New Page
Talk0 Share

The scoring in Chip's Challenge is simple, depending on how many times Chip was killed and how much of the time limit remains. Scoring occurs only when Chip reaches the exit, and is totaled in this manner:

Ccfinish

The window's title is always "Level Complete!", and the leading message can be any of four depending on how many attempts it took Chip to complete the level:

  • Yowser! First Try! = 1
  • Go Bit Buster! = 2 or 3
  • Finished! Good Work! = 4 or 5
  • At last! You did it! = 6 or more

The time bonus, seen as the second value, is the number of seconds remaining on the clock, times 10. In this level, Chip scored a time of 548 seconds, and scored 5,480 points.

The level bonus, seen as the third value, is the level number times 500, multiplied further by .8 per death, and the score is then rounded down at .5 or lower to the nearest point. Should this total decrease below 500, it will stop decreasing. Since this level was completed on the first try, Chip scored 9,000 points, and was therefore playing level 18 in this set.

The level score, value four, is these two addends summed together.

The total score, value five, is Chip's full score in the game at this point, as calculated by Melinda.

Below the total score is a place for a message that declares any score improvement. If there is no improvement, no message is shown. The shown message, stating "You have established a time record for this level!", will be shown whenever a level is completed for the first time. A time improvement will elicit the message "You beat the previous time record by X seconds!", and an improvement in the level bonus will elicit the message "You increased your score on this level by X points!" If both of these happen at the same time, the former message is shown.

Theoretically, the lowest score Chip can achieve is 67,554, scored by recording a time of 1 on every timed level and being killed repeatedly until the level bonus drops under 500. However, in practical play, this is not possible, as Chip assuredly will not survive Jumping Swarm for 399 seconds; Slo Mo may also not be possible to complete with a time of 1.

Unofficial scoring

Aside from the regular scoring, two unofficial competitions are generally held: T-Chip times and tenths reduction.

The T-Chip times are simply scores that would be achieved if 999 were the time limit to an untimed level, and although the scores themselves do not count officially, their AVI solutions are official bold solutions and are used in this guide. Tile World automatically keeps this time as it would any other time, although it is difficult to keep track of because the time limit is never shown.

Tenths reduction is used to compare times that otherwise would have the same score, since normally the in-game clock only ticks down one second every five moves (allowing a faster solution to fail to beat a slower solution's score). The tenth (referring to tenths of a second) is the most basic unit of time in Chip's Challenge; normal moving uses two tenths per tile, or one fifth, sliding uses one tenth per tile, and boosting in a perpendicular direction uses one tenth every two tiles. Arising from this, many routes are done as quickly as possible, with the fewest tenths remaining. Official terminology for tenths is either .X or -.X, which signifies the amount of seconds left either until the next tick or since the previous one.

Notation conversion scale

  • .8 = -.0 = The clock ticked on either a voluntary move into the exit, or on the exact sliding move into the exit when Chip's last non-sliding move was voluntary (and not a spring step). Obviously, this is a frustrating occurrence, and a score ending in .8 will be frequently reported with annoyance. After scoring a .8 time, clock setting is already performed for the next level.
  • .7 = -.1 = 1.5 moves after the last tick, or 3.5 until the next.
  • .6 = -.2 = 2/3 moves.
  • .5 = -.3 = 2.5/2.5 moves.
  • .4 = -.4 = 3/2 moves.
  • .3 = -.5 = 3.5/1.5 moves.
  • .2 = -.6 = 4/1 moves.
  • .1 = -.7 = 4.5/.5 moves.
  • .0 = -.8 = 5 moves, or where the next half-move in the absence of -.9 cases would contain a tick. Since the Lynx Ruleset ticks the clock for one more turn upon entry into the exit, a .0 route played in Lynx will drop to the next second.
  • -.9 (no .X equivalent) = 5.5 moves after the last tick, but the time limit has not decremented. As technically the clock should have ticked at this point, Chip must have used either boosting or a special instance of a spring step. (Note that waiting [1/2] before making a voluntary move into the exit, such that a hypothetical next move would be a spring step, will not create a -.9 time and simply be .0/-.8.) The three specific causes, with examples, are: a force floor override (Flame Boy), a boost which places Chip directly into the exit (Shrinking, Bounce, Oorto Geld II), and Chip making a boost or a spring step onto a sliding space and continuing to slide until he reaches the exit, and the timer was at .0 one space from the exit (I Slide and Just Enough respectively). This is rare, with these being the only six examples in official levels. Because of the continuing clock software in MS, when Chip closes the exit window and moves to the next level, the timer will be down one second from its original setting.

In popular use

The Public TWS always uses the -.X notation, and because of its popularity and ease of use, it is generally fully optimized. Exceptions are few: difficult and/or unlikely routes through random levels, or in the case of some very harsh examples, because it was originally performed in MS and nobody has achieved it in Tile World. The AVI archives are generally not so well-kept, but they have received a major refurbishing by Andrew Bennett to match up with the TWS solutions.

Ad blocker interference detected!


Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.